Comments

11 comments

  • Avatar
    dunxd

    Is it possible to "teach"or calibrate the radiator valves by putting the room thermostat in the same room for a number of days? This would be a nice function as equipping every room with a thermostat seems overkill, but the radiator sensed temperature does not seem accurate.

    5
    Comment actions Permalink
  • Avatar
    Daniele Defilippi

    We are experiencing poor temperature accuracy in all the rooms that do not have the room thermostat when the outside temperature and wind changes. Knowing the limitations of the compensation algorithm it would be nice to have a simpler and less expensive room thermostat, a little box with no display and buttons that just reports the room temperature to the controller. I believe that this can be done quite easily using the electronics inside a radiator thermostat and put it in a room thermostat box like. Just remove the motor driver part and have a firmware with no predictive algorithm. This will improve the temperature control with an accessible cost for most households.

    4
    Comment actions Permalink
  • Avatar
    angelosantagata

    Given the room temperature can depend on a load of factors (Heating of room, height of ceilings, etc), is it possible ot add a "delta" mesurement. Ie we can say whatever temp the trv reads add 2C to it for the real value.

    Currently I am finding the trvs in certain rooms are around 1.5-2C higher than the real temperature, this would enable us a little more control and keep the UI consistent with the real world.

    As a workaround Im setting the trv temperature to 2C + which is fine but then the UI is also 2C out and the insights is a bit squewy

     

    thanks, Wiser is the best!

    2
    Comment actions Permalink
  • Avatar
    Nigel Bullus

    Agree with the above comments.

    We simply need a simple offset we can configure in the zone that the device(s) reside, that offsets the recorded temperature, e.g. +1.5c zone increase means if thermostats reads 20.5c, you see 22c in the app. If you set 22c in your zone schedule, it uses 20.5c when checking if demand is met. 

    Therefore, it doesn't matter if the zone contains smart radiator thermostat(s), room thermostats or combination of both, you offset the zone temperature rather than each device. This compensates for any factory tolerances and deviations between multiple thermostats in a zone. This should be simple to implement and not sure why it's not there already. Just about every other smart thermostat on the market has a temperature offset feature.

     

    3
    Comment actions Permalink
  • Avatar
    Francois Nitenberg

    This is a real issue for us, customers. Overall, it's a good system, but we need to be able to tune that algorithm. As someone else mention before, a cheaper room thermostat would also work nicely. The one currently available a way too expensive for what it is.

    2
    Comment actions Permalink
  • Avatar
    Robin Cawser

    Setting the temperature set point lower is such a bodge of a workaround, it means that thermostat's temperature is not consistent with the other thermostats in the house and requires cognitive effort on our part to remember or write down what each thermostat is calibrated to, this should be part of the software. Other radiator thermostats allow you to apply an offset.

    Right now I'm sat in my living room with the thermostat set to 18 degrees wondering why I'm starting to sweat, when it's -1 outside. Because the radiator thermostat thinks it's 17.3 degrees in here! I have a separate ZigBee temperature and humidity sensor which reads 21 degrees!

    Three wiser app should allow you to calibrate the temperature, or allow you to pair other sensors, or Schneider could sell inexpensive compatible ZigBee temp sensors which could be placed away from the radiator.

    Forget the crappy UI update, improve the functionality first.

    2
    Comment actions Permalink
  • Avatar
    Francois Nitenberg

    I raised a support ticket to find out whether or not this issue is known internally and if they are planning on fixing it anytime soon. I encourage all of you to do the same, just use the help button at the Botton right of this page.

    2
    Comment actions Permalink
  • Avatar
    Topcoat

    I've raised a ticket. Fingers crossed.

    0
    Comment actions Permalink
  • Avatar
    bkav73

    I raised this with the support desk months ago. They said they were aware but nothing has been done. For several of my rooms the issue is more complex than just a simple offset, the temperature error depends on the outside temperature. The colder it is outside the bigger the error. I've seen up to 9deg error when it's -4 outside, and once it's warm outside and the heating's not in use the radiator thermostat gives pretty much the correct temperature. The compensation needs to be a function of the difference between inside and outside temperature. The issue seems most significant in poorly insulated rooms with the radiator on an inside wall.

    1
    Comment actions Permalink
  • Avatar
    James Prior

    What would really help is if the Wiser support team had someone allocated to patrolling these "contribution" comments and actually contributed knowledge to the community themselves! It would add a little confidence that Wiser are interested in their customers and they could provide accurate help and tips for users. Support tickets are on a one-to-one basis, whereas responding to contributions over time would surely help reduce support for common questions and topics? Come on Drayton you've got good products and solutions, you need to up your game a bit on the knowledge side of things - please.

    5
    Comment actions Permalink
  • Avatar
    Amrit

    Completely echo the comments already mentioned here. 

    I am new to the Wiser system and within a week have already found massive inconsistencies with the temperature being reported to actual temperature. 

    At first thought I thought ok no problem, I just increase the set temp by +3 degrees in the bedrooms, however I found it's not even consistently +3 degrees. I found in colder weather, the temp can actually be out by 5 degrees which is insane. I am also learning quite quickly that the Wiser valves don't work well with poorly insulated houses as this skews the temperature further. 

    As stated above, shelling out on additional room stats for massively inconsistent rooms is not really a cost-effective option (£85 each!) so I'm stuck between making do with a rough estimated temperature or just binning them altogether and going back to regular valves. 

    1
    Comment actions Permalink

Article is closed for comments.